Engineered for extreme reliability, our high-precision benchtop and rackmount systems support critical automation, calibration, and power conversion applications.
Chile stands as a global hub for mining exploration, green hydrogen development, and intensive solar energy harvesting. From the high-altitude copper and lithium extractions in the Antofagasta and Atacama regions to the industrial automation centers in Santiago and the maritime complexes of Valparaíso, the operational environment is demanding. Equipment deployed in these sectors must withstand severe environmental challenges: wide temperature fluctuations, dust, high altitudes (often exceeding 3,000 meters above sea level), and grid instabilities.
High-Altitude De-rating (Atacama Specialization): Operating sensitive power electronics at elevations above 2,000m reduces convective air cooling efficiency by up to 20% due to lower air density. MYAMI's custom-engineered Multi-Channel DC Power Supplies address this by incorporating oversized heat sinks, dual-ball bearing active cooling fans, and enhanced dielectric isolation, preventing voltage arcing in thin mountain air.
Furthermore, Chile's aggressive transition toward clean energy (aiming for 80% renewable electricity by 2030) has created an unprecedented demand for battery simulation systems, solar cell emulation, and hydrogen electrolysis testbeds. Testing multi-cell lithium batteries or simulating PV strings under fluctuating sun patterns requires advanced multi-channel DC configurations that offer independent control, galvanic isolation between channels, and sub-millisecond transient response speeds.
Typical industrial environments in Chile require power sources that are not only high-power but also highly granular. A single multichannel DC power supply can replace several bulky single-output units, offering significant rack space savings, reduced cabling, and a centralized control interface. Our technical roadmap focuses on three pillars of innovation:
Each channel is completely isolated electrically, allowing engineers to connect channels in series for higher voltage limits, or in parallel for higher current outputs without cross-channel interference.
Utilizing a hybrid topology (switching pre-regulation with linear post-regulation) our bench and rack DC sources guarantee CV ripple under 1mV RMS, perfect for sensitive semiconductor tests.
Standard support for Modbus-RTU, RS485, RS232, and high-speed CAN bus communication to interface directly with automated PLC systems in Chilean extraction plants.
From raw materials to finished products, our production line is equipped with advanced automated testing stations, active aging chambers, and metrology-grade calibration instruments to guarantee 100% reliability.
Headquartered in the technology hub of Shenzhen, China, Shenzhen Myami Power Technology Co., Ltd. (MYAMI) combines modern automation processes with extreme engineering checks. We understand that a power supply failure on a remote mine in northern Chile can lead to massive operation downtime. Hence, our facility maintains a robust quality management system certified under ISO 9001:2015, and all models undergo a multi-layered check process before export packing.
Raw Material
PCB Checking
Assembling
Debug
Aging
Calibration
QC checking
Packing
Soldering Station
Electronic Screwdriver
PCB Check
Debug
QC check
Multimeter
Hi-pot Tester
Oscilloscope
Each unit undergoes 100% full-load dynamic burn-in testing for at least 24 hours inside heated chambers to weed out early infant mortality of components. We implement strict ESD controls and use state-of-the-art power analyzers, high-bandwidth oscilloscopes, and precision LCR meters (as shown in our testing setups) to calibrate and verify the performance parameters of every single power unit shipped to Chile.
Exporting industrial test instrumentation to Chile demands conformity with strict standards. Our systems are fully compatible with local grid norms and international safety frameworks:
Technical Support and Warranty Policies for Chile: We offer comprehensive technical consults, extended warranties, and drop-shipped critical spare parts to Santiago-based technical partners. This ensures that industrial clients in Antofagasta, Calama, and Concepción receive prompt hardware diagnostics and replacement support.
Technical and procurement answers designed for project managers and system engineers in Chile.
At elevations above 2,000 meters (such as in Calama or Minera Escondida), thin air reduces the heat dissipation capacity of cooling systems. To counter this, we design units with heavy-duty cooling paths, temperature-controlled active cooling fans, and upgraded semiconductor packages. We suggest scaling down maximum load limits by approximately 10% for every 1,000m above 2,000m, or consulting our engineering team to purchase custom units with enhanced cooling paths.
Yes. Our high-precision programmable benchtop and rackmount DC power supplies feature arbitrary waveform generation and SAS (Solar Array Simulator) functions. Engineers can program customized curves via RS485 or CAN protocols to simulate fluctuating sunlight, cloud shading, and temperature changes to test MPPT controllers and inverters.
Our models standardly support RS232, RS485, and USB interfaces using SCPI commands. For heavy-duty automation setups, we offer optional integration of CAN-Bus and Modbus interfaces, enabling seamless remote control and telemetry integration within centralized SCADA platforms.
Absolutely. All export models designed for the South American market conform to CE safety directives and RoHS restrictions. Test reports and certification files can be provided on request for customs clearance.
Standard configurations have a production cycle of 7 to 15 working days. For bulk orders or highly custom multi-channel rack units, lead times range from 3 to 4 weeks. Shipments to major ports like Valparaíso or San Antonio generally take 30-35 days via sea cargo, while urgent shipments can be dispatched via air freight to Santiago International Airport (SCL) within 5-7 days.
Optimized for laboratory R&D, industrial automation systems, and high-power engineering environments across Chile.
Myami Power
